NACE NACE-CIP2-001 Test Engine Dumps Training With 100 Questions
NACE-CIP2-001 Questions Pass on Your First Attempt Dumps for CIP Level 2 Certified
NEW QUESTION 10
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Steam cleaning only
- C. Watterjetting only
- D. Various methods of cleaning
Answer: D
NEW QUESTION 11
It is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION 12
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of acid or caustic splashes
- B. Risk of chemical exposure
- C. Risk of skin
- D. a), b), and c)
Answer: D
NEW QUESTION 13
You should bulk store coatings containing isocyanates
- A. in a heated warehouse.
- B. wherever it is convenient
- C. in a refrigerated warehouses
- D. in a well ventilated area separate from the work place.
Answer: D
NEW QUESTION 14
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. High-pressure water washing
- B. Stoning
- C. Sacking
- D. Acid etching
Answer: D
NEW QUESTION 15
NACE International Standards are developed by:
- A. Standard committees
- B. Government mandates
- C. International mandates
- D. Regional mandates
Answer: A
NEW QUESTION 16
A single component water borne acrylic coating cures by:
- A. Co-Reaction
- B. Solvent Evaporation
- C. Oxidation
- D. Coalescence
Answer: D
NEW QUESTION 17
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Challenge the supervisor's authority
- B. Express a willingness to work with the site team and follow the specification
- C. Defend the previous inspector
- D. Suggest to the Owner that the supervisor should be removed from site
Answer: B
NEW QUESTION 18
Corrosion is the reverse process of
- A. steel manufacturing.
- B. hot dipping.
- C. flaking.
- D. galvanic deterioration.
Answer: A
NEW QUESTION 19
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Verbally challenge the NCR
- C. Request a re-blast of the item in question
- D. Review the NCR with the other Inspector
Answer: A
NEW QUESTION 20
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Cost
- C. Safety
- D. Iron content
Answer: D
NEW QUESTION 21
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Inorganic Coatings
- B. Polyurea
- C. Latex
- D. Organic coatings
Answer: A
NEW QUESTION 22
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Acid etching
- B. High-pressure water washing
- C. Stoning
- D. Sacking
Answer: D
NEW QUESTION 23
Coating surveys may include which steps?
Select All That Apply:
- A. Schedule the remedial work
- B. Summarize the collected data
- C. Develop a survey plan
- D. Evaluate the coatings performance
Answer: A,B,C,D
NEW QUESTION 24
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the Inspector doesn't have to read the entire specification
- C. So the contractor has a single document to reference
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION 25
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection and Non-destructive testing
- B. All types of inspection without supervision
- C. Visual inspection, Non-Destructive and Destructive testing
- D. Visual inspection only
Answer: C
NEW QUESTION 26
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Coal Tar Enamel
- B. 2-Layet Polyethylene (PE)
- C. 3-Layet Polyethylene (PE)
- D. Concrete
Answer: D
NEW QUESTION 27
The HATE adhesion tester uses
- A. a special tape to apply pressure to the test dolly.
- B. a hydraulic piston to apply pressure to the test dolly.
- C. compressed air to apply pressure to the test dolly.
- D. mechanical means only to apply pressure to the test dolly.
Answer: B
NEW QUESTION 28
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 2-Layer Polyethylene (PE)
- C. 3-Layer Polyethylene (PE)
- D. Fusion Bonded Epoxy
Answer: C
NEW QUESTION 29
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and submit the reports without any further action
- B. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- C. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- D. Correct the errors yourself and suggest the Level 1 inspector be replaced
Answer: C
NEW QUESTION 30
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Ultra Sonic DFT Gauge
- C. Tooke Gauge
- D. Eddy Current Gauge
Answer: C
NEW QUESTION 31
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Lighting
- B. Air changes
- C. a), b), and c)
- D. Structural integrity
Answer: C
NEW QUESTION 32
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. manufacturer of the equipment.
- C. time of the year (winter/summer).
- D. coating type.
Answer: D
NEW QUESTION 33
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 single rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 50 double rubs with a saturated cloth.
- D. 25 double rubs with a saturated cloth.
Answer: C
NEW QUESTION 34
Surface preparation methods for Non-ferrous metals are:
- A. Specific for each type of Non-ferrous metal
- B. The same as for Ferrous metals
- C. The same for all Non-FetT0us metals
- D. Not required
Answer: A
NEW QUESTION 35
......
NACE-CIP2-001 Practice Test Pdf Exam Material: https://www.dumpsfree.com/NACE-CIP2-001-valid-exam.html
NACE-CIP2-001 Answers NACE-CIP2-001 Free Demo Are Based On The Real Exam: https://drive.google.com/open?id=1rEfbT6EaOrA9JR1U-bUbjohRVHTRkYpj