NACE NACE-CIP2-001 Practice Test Pdf Exam Material
NACE-CIP2-001 Answers NACE-CIP2-001 Free Demo Are Based On The Real Exam
NACE-CIP2-001 Certification Exam is a comprehensive test designed to assess the knowledge and skills of coating inspectors at the Level 2 designation. Coating Inspector Level 2 certification is issued by the National Association of Corrosion Engineers (NACE), a globally recognized organization that provides training and certification programs in the field of corrosion prevention and control.
NEW QUESTION # 40
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Tooke Gauge
- B. Eddy Current Gauge
- C. Magnetic Gauge
- D. Ultra Sonic DFT Gauge
Answer: A
NEW QUESTION # 41
Surface preparation methods for Non-ferrous metals are:
- A. Specific for each type of Non-ferrous metal
- B. Not required
- C. The same as for Ferrous metals
- D. The same for all Non-FetT0us metals
Answer: A
NEW QUESTION # 42
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Different than air blast cleaning
- B. The same as air blast cleaning
- C. Comparable to air blast cleaning
- D. Slightly different to air blast cleaning
Answer: B
NEW QUESTION # 43
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the two end points identified in the standard
- C. Record the percentage of failure
- D. Record the highest value attained
Answer: B
NEW QUESTION # 44
Pre-cleaning of work pieces will NOT remove
- A. mill scale.
- B. oil or grease.
- C. snow, ice or water.
- D. dirt.
Answer: A
NEW QUESTION # 45
NACE Standards include:
- A. Material Requirements
- B. a) & b)
- C. Standard Practices
- D. a) only
Answer: B
NEW QUESTION # 46
When observing fabrication defects the NACE Inspector should:
- A. Write an NCR and call the fabricator
- B. Consult the specification to determine how they should be treated
- C. Stop the job immediately
- D. Require they be corrected prior to coating
Answer: B
NEW QUESTION # 47
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. reduce magnetic polarity.
- C. protect the transported product.
- D. provide protection against soil chemicals.
Answer: C
NEW QUESTION # 48
Galvanizing performs best in which of the following exposures:
- A. pH above 12
- B. pH between 5-10
- C. pH below 4
- D. pH of 13
Answer: B
NEW QUESTION # 49
Dehumidification is defined as the removal of moisture vapor from the air to
- A. provide worker comfort.
- B. raise its relative humidity.
- C. lower its temperature
- D. lower its dew point,
Answer: D
NEW QUESTION # 50
A reinforced coating is
- A. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. equally resistant to abrasion and impact as a non-reinforced coating.
- C. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to movement and impact as a non-reinforced coating.
Answer: C
NEW QUESTION # 51
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Require the Applicator to remove the coating
- B. Ignore the situation
- C. Stop the job
- D. Advise the Owner and write a Non-Conformance report
Answer: A
NEW QUESTION # 52
When conducting inspections the Inspector should follow which standards:
- A. Australian standards in Australia
- B. ISO standards in Europe and Asia
- C. NACE and SSPC standards in North America
- D. The specified standards
Answer: D
NEW QUESTION # 53
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method A - X Cut
- B. Method B - Cross Hatch
- C. Method A - Cross Hatch
- D. Method B - X cut
Answer: A
NEW QUESTION # 54
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. No difference from any other coating
- B. A very high reading
- C. Cold flow or creep
- D. A very low reading
Answer: C
NEW QUESTION # 55
......
NACE-CIP2-001 [Dec-2023] Newly Released] Exam Questions For You To Pass: https://www.dumpsfree.com/NACE-CIP2-001-valid-exam.html
NACE NACE-CIP2-001 Exam: Basic Questions With Answers: https://drive.google.com/open?id=1lTqIzQyUiceWuLv9-AZlLnBv91CXEgb3