NACE-CIP1-001 Self-Study Guide for Becoming an Coating Inspector Level 1 Expert
NACE-CIP1-001 Study Guide Realistic Verified NACE-CIP1-001 Dumps
NEW QUESTION # 38
The Inspector should record the serial numbers of inspection instruments:
- A. Each time the instrument is used
- B. Only if the instrument is suspected of not working properly
- C. Only if the specification requires it
- D. Only when verifying accuracy of the instrument
Answer: A
NEW QUESTION # 39
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Assume the role of the Safety Inspector
- C. Check the PPE used by the Applicators
- D. Check the credentials of the Safety Officer on site
Answer: A
NEW QUESTION # 40
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Ensure the instrument is within calibration parameters
- C. Be trained on how to use the instrument
- D. a), b) & c)
Answer: D
NEW QUESTION # 41
Polymerization is the process of:
- A. All thermoplastic coatings
- B. Monomers joining together
- C. Monomers telegraphing
- D. All organic coatings
Answer: B
NEW QUESTION # 42
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor
- B. Break the blisters to see what's inside
- C. Document the problem and advise the Contractor and Owner's representative
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
Answer: C
NEW QUESTION # 43
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. sagging.
- B. cracking.
- C. holiday.
- D. checking.
Answer: C
NEW QUESTION # 44
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the job specification as a guide
- B. Call the coating manufacturer for clarification
- C. Call the person who wrote the specification for clarification
- D. Use the product data sheet as a guide
Answer: A
NEW QUESTION # 45
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
Answer: B
NEW QUESTION # 46
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- B. NACE SP 0188
- C. SSPC PA 2
- D. NACE SP 0178
Answer: A
NEW QUESTION # 47
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Relative Humidity
- C. High Surface Temperature
- D. Low Surface Temperature
Answer: B
NEW QUESTION # 48
Safety Data Sheets must be carefully reviewed by:
- A. The Owner's personnel
- B. All personnel involved in the job
- C. The Inspection personnel
- D. The Application personnel
Answer: B
NEW QUESTION # 49
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Keep doing the checks and consult the Owner's representative for direction
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Skip the checks and just record the same readings as you have been getting
Answer: B
NEW QUESTION # 50
ISO ST 3 is described as:
- A. Thorough blast cleaning
- B. Very Thorough hand or power tool cleaning
- C. Thorough hand tool cleaning
- D. Very Thorough power tool cleaning
Answer: B
NEW QUESTION # 51
ISO SA 3 is directly equivalent to:
- A. NACE No. 3/SSPC SP 6
- B. None of the above
- C. NACE No. 1/SSPC SP 5
- D. NACE No. 2/SSPC SP 10
Answer: B
NEW QUESTION # 52
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Always handwritten
- C. Timely, accurate and concise
- D. Submitted before the end of the job
Answer: C
NEW QUESTION # 53
Stripe coats are best applied by:
- A. High volume low pressure spray
- B. Conventional spray
- C. Airless spray
- D. Brush
Answer: D
NEW QUESTION # 54
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. the highest temperature at which moisture forms on a steel surface.
Answer: B
NEW QUESTION # 55
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. blistering.
- C. checking.
- D. alligatoring.
Answer: C
NEW QUESTION # 56
SSPC SP 1 identifies the use of:
- A. Organic solvents
- B. Inorganic solvents
- C. Biodegradable detergents
- D. A wide variety of materials
Answer: D
NEW QUESTION # 57
Check abrasive blast pressure close to the
- A. blast pot
- B. blast nozzle
- C. compressor
- D. substrate
Answer: B
NEW QUESTION # 58
Checking is
- A. an exposed area of the substrate or previous coat material, caused by poor application technique.
- B. a fine crack in the surface of a coating that rarely reaches the substrate
- C. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- D. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
Answer: B
NEW QUESTION # 59
Removal of surface contaminants is done by:
- A. Abrasive blasting
- B. Scarifying
- C. A combination of methods
- D. Waterjetting
Answer: C
NEW QUESTION # 60
What is used to determine compressed air cleanliness?
- A. Needle pressure gauge
- B. Psychrometer
- C. Blotter test
- D. Profilometer
Answer: D
NEW QUESTION # 61
......
Valid NACE-CIP1-001 Exam Dumps Ensure you a HIGH SCORE: https://www.dumpsfree.com/NACE-CIP1-001-valid-exam.html
NACE-CIP1-001 Questions & Practice Test are Available On-Demand: https://drive.google.com/open?id=1hv1xtPWxVJfyCUuF2cz21xLOX3b87G3K