ASQ CRE Deluxe Study Guide with Online Test Engine
CRE dumps review - Professional Quiz Study Materials
NEW QUESTION 247
In the Taguchi design methodology, what are noise factors?
Response:
- A. Factors that influence variation in the output
- B. Factors that strongly influence the mean response.
- C. Factors that impact tolerance design
- D. Factors that maximize parameter design.
Answer: A
NEW QUESTION 248
What is this system's reliability at 700 hours?
Component failure data is : - Failure rate of A = 0.0007 failures/hr - Reliability of B = 0.92 - MTTF of C =
1400 hours - Reliability of D = 0.85.
Response:
- A. 0.994
- B. 0.998
- C. 0.952
- D. 0.986
Answer: B
NEW QUESTION 249
What is the failure rate of a system composed of three components, each of which can cause a system failure, and which have the following information?
Response:
- A. 0.00913 f/hr.
- B. 0.00192 f/hr
- C. 0.00671 f/hr
- D. 0.00258 f/hr.
Answer: D
NEW QUESTION 250
Which answer is the expected value of the Poisson distribution shown below?
Response:
- A. μ
- B. μ 2
- C. μe - μ
- D. e - μ
Answer: A
NEW QUESTION 251
Which of the following is NOT an objective of a data collection program?
Response:
- A. To demonstrate internal reliability.
- B. To produce reliability reports.
- C. To validate vendor supplied items.
- D. To demonstrate reliability to customers.
Answer: B
NEW QUESTION 252
What is the reliability of the logic diagram to the below?
(Assume statistical independence of all 3 components)
Response:
- A. 0.9905
- B. 0.996
- C. 0.94
- D. 0.994
Answer: D
NEW QUESTION 253
Root cause failure analysis is necessary to identify and correct basis problems. Usually a priority of failure mode is established. This classic or traditional approach to improvement results in which of the following?
Response:
- A. Defect reduction.
- B. Zero defects.
- C. Catastrophic problem reduction.
- D. Special cause reduction.
Answer: A
NEW QUESTION 254
Feedback channels for the planning, management and assessment of product safety should include:
I. Both official and unofficial sources.
II. Phone, fax, mail and questionnaire sources.
III. Captured company process information.
Response:
- A. I, II and III
- B. I and III only
- C. II only
- D. II and III only
Answer: A
NEW QUESTION 255
Which answer correctly describes the experimental design on the left?
Response:
- A. Latin Square.
- B. Randomezed Complete Block
- C. Greaeco-Latin Square.
- D. Youden Square.
Answer: C
NEW QUESTION 256
When a defense is prepared for a product liability action, all of the following would be considered elements of the assumption of risk the plaintiff must have EXCEPT:
Response:
- A. Contributed to the injury through negligence.
- B. Voluntarily undertaken the risk.
- C. Had knowledge of the risk
- D. Understood the consequence of the risk.
Answer: A
NEW QUESTION 257
The continuous improvement process can be guided by several techniques. Which of the following is the BEST approach?
Response:
- A. The original seven quality tools
- B. Multi-vari charts
- C. Use of the PDCA cycle
- D. The new seven quality management tools
Answer: C
NEW QUESTION 258
If the plating time of a tube increases as the inside diameter decreases, then the correlation coefficient for the insider diameter versus plating time would be:
Response:
- A. Greater than 1
- B. Between 0 and -1
- C. Equal to 1
- D. Between 0 and +1
Answer: B
NEW QUESTION 259
Design reviews should have sufficient information available to make their meetings worthwhile. Formal controls (specifications, drawing controls, etc.) should begin with the first design review. This approach is referred to as:
Response:
- A. Configuration control.
- B. Documentation control.
- C. Quality systems documentation.
- D. Standards organization.
Answer: A
NEW QUESTION 260
Which of the following action will help eliminate the effects of extraneous factors in a designed experiment?
Response:
- A. Selecting factor levels.
- B. Randomizing the experiment.
- C. Fractionating the experiment.
- D. Repeating the experiment under different conditions.
Answer: B
NEW QUESTION 261
Customer feedback and field data could NOT normally:
Response:
- A. Provide information for company's management.
- B. Provide information for product improvement.
- C. Provide information for reliability performance measures
- D. Allow management to identify who is to blame.
Answer: D
NEW QUESTION 262
......
Exam Questions Answers Braindumps CRE Exam Dumps PDF Questions: https://www.dumpsfree.com/CRE-valid-exam.html
CRE Test Prep Training Practice Exam Questions Practice Tests: https://drive.google.com/open?id=18N7FfZCFa9xk7Tady5g_zIpNJLIElOYZ